門套現在是沒有標準規格的，都是按照實際情況來定，不過正常門套厚度在12毫米以上為宜，若在12毫米以下，踢腳線會露出一個口來，因此厚度不足12毫米的門套線，需要加層。若較為高檔的房屋裝修或開發商未做統一規定的話，可以根據家里的門洞尺寸來定做的。

　　There is currently no standard specification for door frames, which are determined based on actual conditions. However, the normal thickness of door frames should be above 12 millimeters. If it is below 12 millimeters, the skirting board will expose a hole. Therefore, door frame lines with a thickness less than 12 millimeters need to be layered. If the high-end house decoration or developer does not have unified regulations, it can be customized according to the size of the door opening in the home.

　　門套怎么固定在墻上

　　How to fix the door frame on the wall

　　1、基本框架：選擇結實的木頭做芯材，按照原先良好的門套尺寸將木板裁成等寬大小，做成門框的基本框架。首先確定位置，用紅外線水平儀在墻上標出水平線，然后測量出門洞的大小，兩邊用墨斗彈垂直線。

　　1. Basic framework: Choose sturdy wood as the core material, cut the wooden board into equal width sizes according to the original good door frame size, and make the basic framework of the door frame. Firstly, determine the position, mark the horizontal line on the wall with an infrared level, and then measure the size of the doorway. Use an ink fountain to draw straight lines on both sides.

　　2、墻上打眼：用充氣鉆在墻上打眼兒，加上木楔，這個時候記得做好標記。這個時候要將門套各個方向垂直水平安裝，保證框架直角是否平直，然后將釘子穿過門框，釘入木楔子，將門框固定在墻上。

　　2. Wall drilling: Use an inflatable drill to drill holes on the wall, add wooden wedges, and remember to mark them at this time. At this point, the door frame should be installed vertically and horizontally in all directions to ensure that the right angle of the frame is straight. Then, nails should be inserted through the door frame and into the wooden wedges to fix the door frame to the wall.

　　3、一層疊級：將門套基本框架固定好以后，就可以做疊級了，這個目的是為了日后開關門關更加方便，距離大概在4-5CM左右。

　　3. One layer stacking: After fixing the basic frame of the door frame, the stacking can be done for the convenience of opening and closing the door in the future, with a distance of about 4-5CM.

　　4、貼面板：以上步驟安裝完畢后，就開始貼面板了(先檢查同一扇門的面板是否色差相近，邊緣有無毛刺)，首先要測量好尺寸，接著裁剪面板，交界處縫隙嚴密。

　　4. Panel pasting: After the above steps are installed, it is time to start pasting the panels (first check whether the panels of the same door have similar color differences and whether there are burrs on the edges). First, measure the size, then cut the panels, and ensure that the gaps at the junction are tight.

　　5、安裝木線條：當面板貼完之后，就可以開始安裝木線條了。由里向外保留出1CM的距離，做上標記，然后將裁好的木線條根據標記進行安裝，這樣做會讓整體的門套就更加美觀了。這個時候一定要注意門框與地面之間大概留取5CM的空間，保證其他工序正常進行，如地面找平、貼地板或瓷磚的時候，可以有足夠的空間。

　　5. Installation of wooden strips: After the panel is pasted, you can start installing the wooden strips. Leave a distance of 1cm from the inside out, mark it, and then install the cut wooden wire according to the mark. This will make the overall door frame more beautiful. At this time, it is important to leave a space of approximately 5CM between the door frame and the floor to ensure that other processes proceed normally, such as leveling the floor, tiling, or tiling, with sufficient space.

　　6、門擋線：用射釘槍把門擋線釘在門套線上，再固定好入門擋線和靜音條。正好壓住前后門框線的接縫處，釘子要注意，不要一次性全釘進去，因?yàn)橛锌赡軙?huì)導致門框歪斜，將多余的木塞鋸掉。

　　6. Door stop line: Use a nail gun to nail the door stop line onto the door frame line, and then fix the door stop line and mute strip. Just press down on the seam of the front and rear door frame lines, be careful not to nail all at once, as it may cause the door frame to tilt and saw off excess wooden plugs.

　　7、表面清潔：等門套安裝好以后，最后做好木門套的表面清潔工作。

　　7. Surface cleaning: After the door frame is installed, finally clean the surface of the wooden door frame.

　　本文由 濱州不銹鋼電梯門套  友情奉獻.更多有關的知識請點擊  http://www.hq-ad.com/   真誠的態度.為您提供為全面的服務.更多有關的知識我們將會陸續向大家奉獻.敬請期待.

　　This article is a friendly contribution from Binzhou Stainless Steel Elevator Door Frame For more related knowledge, please click http://www.hq-ad.com/ Sincere attitude To provide you with comprehensive services We will gradually contribute more relevant knowledge to everyone Stay tuned